TA879 : Experimental Evaluation of the Seismic Performance of Reinforced Concrete Beam–Column Joints with a 10-Degree In-Plane Column Inclination under Cyclic Loading
Thesis > Central Library of Shahrood University > Civil & Architectural Engineering > MSc > 2026
Authors:
[Author], Jalil Shafaei[Supervisor]
Abstarct: شکل‌پذیری و انرژی مستهلک‌شده ارزیابی شدند. نتایج آزمایش‌ها نشان داد که نمونه اتصال مایل 10 درجه در مقایسه با نمونه اتصال قائم غیرلرزه‌ای، به‌ترتیب 69/17درصد افزایش در مقاومت حداکثر، 50/12 درصد افزایش در سختی مؤثر و 58/22 درصد افزایش در انرژی مستهلک‌شده را نشان داد، در حالی که شکل‌پذیری آن 08/2 درصد کمتر بود. همچنین، در مقایسه با نمونه اتصال قائم لرزه‌ای، مقاومت حداکثر، سختی مؤثر و انرژی مستهلک‌شده نمونه اتصال مایل 10 درجه به‌ترتیب 87/3، 5 و 25/11 درصد افزایش یافت و شکل‌پذیری آن نیز 44/4 درصد بیشتر بود. در مجموع، وجود انحراف درون صفحه‌ای 10 درجه‌ای ستون، در نمونه مورد بررسی موجب بهبود مقاومت، سختی مؤثر و قابلیت اتلاف انرژی شد، در حالی که شکل‌پذیری در محدوده نسبتاً نزدیک به دو نمونه قائم باقی ماند. کلمات کلیدی: اتصال تیر-ستون، جزئیات لرزه‌ای، ستون مایل، جابه‌جایی نسبی، بارگذاری چرخه‌ای Abstract Beam-column joints are among the most critical regions of reinforced concrete frxames under seismic loading, and deficiencies in reinforcement detailing or changes in column geometry can significantly affect their seismic performance. In particular, the presence of an inclined column can alter the force-transfer mechanism, stress distribution, and concentration of deformations within the joint region. Given the use of inclined columns in certain structural systems and the limited number of experimental studies addressing their seismic behavior, investigating the seismic performance of such joints is of particular importance. In this study, the seismic behavior of three 1:2-scale reinforced concrete beam-column joint specimens was experimentally investigated under quasi-static cyclic loading. The specimens consisted of a vertical joint with non-seismic reinforcement detailing, a vertical joint with seismic reinforcement detailing, and a joint with seismic reinforcement detailing and a column inclined at 10° in the plane of the frxame. The specimens were subjected to a constant axial load and lateral loading with progressively increasing displacement amplitudes. During the tests, the development of damage and cracking was monitored, and hysteresis and envelope curves were obtained. The maximum strength, effective stiffness, ductility, and energy dissipation capacity were subsequently evaluated. The experimental results showed that, compared with the vertical joint with non-seismic detailing, the 10° inclined-column joint exhibited 17.69% higher maximum strength, 12.50% higher effective stiffness, and 22.58% higher dissipated energy, while its ductility was 2.08% lower. Compared with the vertical joint with seismic detailing, the 10° inclined-column joint exhibited 3.87% higher maximum strength, 5.00% higher effective stiffness, and 11.25% higher dissipated energy, while its ductility was 4.44% higher. Overall, the results indicate that, for the tested specimen, a 10° in-plane column inclination improved the maximum strength, effective stiffness, and energy dissipation capacity, while the ductility remained within a relatively similar range to that of the two vertical-column specimens.
Keywords:
#_Beam-column joint #seismic detailing #inclined column #relative displacement #cyclic loading_ Keeping place: Central Library of Shahrood University
Visitor: