Shahrood University Of Technology Thesis
Shahrood University of Technology
- Preparation, Rheological Characterization and Modeling of Anisotropic Magnetorheological Elastomers under Shear Loading
- Thermodynamic and economic assessments and performance analysis of combined cooling, heating and power (CCHP) systems with internal combustion engine as prime mover baxsed on produced biogas of wastewater treatment plants
- Vibration Analysis of a Porous Axisymmetric Cylindrical Shell under Thermomechanical Load baxsed on First-order Shear Deformation Theory
- A fuzzy decision-making model for optimal design of a hybrid solar/wind/diesel/battery/hydro system for supplying a reverse osmosis desalination unit: Case study
- Analytical and numerical study of flow and heat transfer of conical magnetorheological bearing
- Anomaly detection in electromechanical impedance method using stochastic differential equations
- Design and analysis of composite frangible joint ring
- Design and fabrication of RFSW mechanism and investigation of variables affecting the joint quality of aluminum pipes reinforced by micro particles
- Energy, exergy, economic and environmental analysis of combined cooling, heating and power (CCHP) system with hybrid prime mover including solid oxide fuel cell and gas turbine with multi-effect desalination system (MED) baxsed on organic Rankine cycle with ejector cooling system
- Energy, exergy, economic and environmental analysis of combined cooling, heating and power (CCHP) system baxsed on hybrid prime mover of molten carbonate fuel cell and gas turbine with multi-effect desalination system and absorption cooling system
- Estimating the amount of water loss due to evaporation in the Kalpoosh dam of Semnan province and investigating its reduction methods
- Experimental determination of mechanical power of a 3-bladed 110 cm diameter rotor versus wind speed
- Experimental study of the aerodynamics of micro airfoils with wavy surface and the use of different patterns inspired by nature
- Improve the estimation of heat flux on cancerous tissue in the treatment of hyperthermia
- Investigation of Dynamic Surface Properties of Native Plant Extract Solution at the Liquid-Air Interface Using Pendant Drop and Their Effects on Produced Foam Specifications
- Investigation of Heat Transfer of Falling Film Evaporation and Multi Effect Desalination Process under Vacuum Condition in Small Scale
- Laboratory investigation of the effect of cooling the thermal photovoltaic system of CPC type using energy and water storage materials
- Numerical and experimental analysis of Jamming Phenomenon in Positioning of Circular-Section Workpiece on Horizontal Surface
- Numerical modeling of the effect of blast loading on slope stability
- On the effect of warping on the inter modules distance in a single row of a sun tracking PV plant
- Performance Optimization of the Indirect Fired Water-Bath Heaters Used in City Gate Stations
- Technical analysis and performance optimization of a multi-generation system including thermal photovoltaic panel cooled by nanofluid. Desalination. Orc and electrolyzer system
- Technical and economic analysis for investigation the potential of thermal recovery of waste streams in a steel factory by application of a hybrid poly-generation system to generate power and hydrogen
- Technical and economic evaluation of desalination of Iranshahr steam power plant effluents by means of heat losses of different units using MED desalination plant
- Thermodynamic analysis and performance improvement of a two-stage compression-ejection hybrid refrigeration system
- A fuzzy controller design for chemotherapy of cancer patients
- Analysis of trapping /separation of solid particles in a microsystem containing fluid flow with the presence of a non-uniform electric field
- Analytical and experimental investigation of isostatic cold pressing of ceramic powder with rubber to make a conical body
- Analytical solution of thermoelastic and semi-analytical of creep for pressurized truncated conical shell with variable thickness using FSDT
- Assistive knee robot design baxsed on the biomechanical characteristics of the knee
- Buckling and stress failure analysis of composite cylindrical shells under mechanical and thermal loading
- Classification of Motor Imagery EEG Signals using CNN baxsed on stratistical and time-frequency domain
- Construction and experimental analysis of water-silica gel surface solar absorption cooling system
- Design and manufacture of smart microairfoil using suction, blowing and experimental investigation of aerodynamic properties
- Determining of the Stress Intensity Factor of an Infinite Orthotropic Plane Containing Cracks Emanating from a Circular Cutout under Uniform Heat Flux
- Dynamic characterization and modeling of anisotropic magnetorheological elastomers under tensile-compressive loadings
- Energy, exergy, economic and environmental analysis of combined cooling, heating , power and hydrogen (CCHPH) system baxsed on solar tower by steam methane reformer (SMR) and PEM water electrolysis (PEMWE)
- Experimental Analysis of Fracture and Vuggy Effects in a Multi-Porosity Media: Enhanced Oil Recovery Approach
- Experimental investigation of bending behavior and axial buckling of basalt/epoxy hybrid composites containing carbon nanotubes
- Experimental investigation of the behavior of double-curved composite sandwich panels containing nanoparticles with mechanical fasteners under edgewise compression
- Experimental investigation of the effect of increasing the blade length at the root on the three-blade wind turbine rotor power
- Experimental investigation of ultrasonic vibration on frictional behavior of the sheet mextals during the draw bending process baxsed on the measuring of deformation distribution
- Experimental study and statistical analysis of variables affecting the mechanical properties of printed PETG samples using FDM technology
- Experimental Study of Bubble Rising in Boger Fluids
- Experimental study of thermoelectric and phase change materials to improve the performance of a photovoltaic system including a compound parabolic concentrator
- Feasibility study of the applicability of additive laxyer manufacturing technology in fabrication of a drilling fixture
- Investigating and simulating the drag force and heat transfer on a flat plate with limited thickness in severe flow imbalance conditions in dilute gas conditions by DSMC
- Investigation of thermal stress distribution around a non-circular cutout in a functionally graded plate
- manufacture and explosiv test rims frangible joint composite
- Modeling and thermodynamic analysis of vacuum crystallizer with heat pump
- Nonlinear vibrations analysis of an axisymmetric annular hyperelastic plate with moderately large deflection using shear deformation theory
- Numerical analysis on the effect of boundary laxyer diverter for the ramped inlet
- Numerical investigation of particles’ dynamics in a lung-on-chip with porous membrane
- Numerical simulation of the performance of the proposed combined mechanism of increasing and decreasing the lift force around the airfoil for the passive control of the required aerodynamic forces
- Numerical Study of Particle Flow in A Porous Medium By LbM-IBM
- Numerical study of two-phase flow in porous media micro-models with Enhance Oil Recovery
- Optimization of resistance spot welding in low carbon steel using an adhesive
- Simulation and Analytical Study of the Effect of Composite Solid Propellants (Nitramine baxsed) on the Erosion Rate of a Graphite Nozzle for Different Operating Pressures
- Stiffness-baxsed synthesis of the four-bar lixnkage with flexure joints using optimization algorithms
- Synthesis of the planar lixnkages by optimization of the closed-loop system using fractional order PID controller
- Technical and economic analysis and optimization of an integrated system including Molten Carbon Fuel Cell, Rankine / Kalina cycle, and absorption refrigeration system
- Technical And Economic Analysis Of A Multiple Production System baxsed On Gas Turbine Combined Cycle For Power Generation, Cooling, Fresh Water, Hydrogen
- Technical and economic modeling and optimization of combined cooling, heating and power system baxsed on internal combustion and Stirling engines
- Technical, Economical and Environmental Analysis of Gas Refinery Incinerator in order to Temperature Control and Energy Regeneration
- The combined effect of Induced Electrokinetics and Dielectrophoresis on Particle guidance in Microchannel
- Thermodynamic and economic analysis of a liquid desiccant system with solar regeneration
